Here below you can get a bunch of professional details relating to How to Install a Bathtub.
Setting up a bathtub isn't specifically brain surgery, but it does call for solid plumbing, carpentry, and occasionally, tiling skills. Changing an old bathtub with a brand-new one is likewise a reasonably difficult task. If the old tub is conveniently obtainable, the project can relocate speedily; if you need to open a wall to get rid of the old tub as well as place the new bath tub, the task is a lot harder. In either case, the job is within a home handyman's skills, although you will certainly require a helper to vacate the old tub as well as embeded in the brand-new one. Make sure you have actually qualified yourself for the work and are comfortable trying it. Rather than hiring a professional to take control of a halfway-completed project, it is better to take into consideration utilizing one prior to you start. Possibilities are you might need an expert plumber to make tube links.
This article will certainly assist you set up a brand-new bathtub in your shower room if you have actually currently purchased a new bathtub and also do not need to alter the plan of your previous water pipes.
Your tools and material list should consist of the following:
Planning for the Installation
Firstly, the supporting framework provided with the bathroom should be fitted (if required) according to the producer's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is important to make sure that if the tap comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets system to avoid pressure on the bath tub.
Fit the versatile faucet ports to the bottom of both faucets utilizing 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. See to it you make use of every one of the provided washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath must now prepare to be suited its final position.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you ought to do is disconnect the water. After doing so, turn on the faucets to drain pipes any water staying in the system. The procedure of eliminating the existing faucets can be fairly bothersome as a result of the limited accessibility that is commonly the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the continuing to be water that will certainly originate from the pipelines. When the supply pipelines have been removed, use the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary faucets from transforming during this process. When the taps have been eliminated, the holes in the bath/basin will need to be cleansed of any type of old sealing compound.
Before moving on to fit the brand-new taps, compare the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the new taps, then a shank adapter is required for the brand-new taps to fit.
Mounting the Tub
Using both wood boards under its feet, place the bath tub in the needed position. The wood boards are valuable in evenly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 small factors.
The next objective is to guarantee that the bath tub is leveled all round. This can be achieved by examining the spirit level as well as changing the feet on the bath tub up until the spirit level checks out level.
To mount faucets, fit the bottom of the outermost adaptable tap connector to the appropriate supply pipeline by making a compression join; after that do the same for the various other tap.
Turn on the water supply and also check all joints and also new pipework for leakages and also tighten them if needed. Fill up the bath tub and likewise inspect the overflow electrical outlet as well as the regular outlet for leaks.
Ultimately, fix the bathroom paneling as defined in the producer's instruction manual. Tiling as well as securing around the bathtub ought to wait till the bathtub has been made use of at least once as this will certainly settle it into its final setting.
Suitable New Taps
If the tails of the new faucets are plastic, then you will require a plastic adapter to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end gives a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will need minimizing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the mounting hole in the bath/basin guaranteeing that the washers are in location between the faucet as well as the sink. Protect the faucet in position with the manufacturer provided backnut. Once the tap is firmly in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with typical faucet connectors. The former type must be attached to the faucet finishes initially, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bath fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to crack a rigid seal, causing the water to penetrate the wall in between the bathroom and also the tiling, bring about difficulties with wetness and possible leaks to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your components as well as installations. They are offered in tubes as well as cartridges, and are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of soaked newspaper or soft rope. Remember to constantly fill up the bathtub with water before securing, to permit the motion experienced when the tub is in use. The sealer can split relatively early if you do not consider this motion before sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise quickly available on the market. It is recommended to fit the tiles making use of waterproof or water resistant adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you liked our topic on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Many thanks for finding the time to read through our content. Do you know about another person who is occupied with the subject? Take a moment to promote it. Thanks for your time. Please visit our blog back soon.
Explore